Toughened safety glass in Radcliffe

What should toughened safety glass cost in Radcliffe?

Expect £114 to £414 including VAT (£95 to £345 plus VAT) per pane for toughened safety glass in Radcliffe. The written quote names the glass makeup, the price and the lead time before you commit.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

What you can specify

Breaks into small blunt fragments
Clear, tinted, obscure, low-iron and sandblasted finishes
Made to BS EN 12150 and marked for identification
Heat-soaked option for large and overhead panes
Four to five times the strength of annealed glass
Single panes or the outer pane of a sealed unit

Fitting in Radcliffe and nearby

We arrange surveys and fitting in Radcliffe and across the M26 postcode district, as well as in nearby Whitefield (1 mile) and Prestwich (3 miles). Dates depend on installer availability.

Greater Manchester mixes city-centre offices and converted mills with Victorian terraces in Salford, Oldham and Bolton, suburban high streets and large out-of-town retail parks.

Good candidates for toughened safety glass:

Balustrades in a laminated toughened makeup
Frameless office partitions and doors
Panes below 800 mm in homes and offices
Shower screens and splashbacks

Before the glass is ordered

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Glazing rules in England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Fire-rated glass is different

Glass in fire doors, fire screens and protected escape routes has to be fire-rated glass tested as part of that door or screen system, under Approved Document B and the fire safety duties of the building's responsible person. Laminated and security glass are not fire-rated unless the product says so. Where a pane needs both fire and security performance, it must be a product tested for both.

How it works

Guide price online or by phone
Survey in Radcliffe
Accept the fixed quote
Fitted by glaziers working under our contract

Toughened safety glass in Radcliffe: questions

Do you cover Whitefield as well as Radcliffe?

Yes. As well as Radcliffe, we can arrange surveys in nearby Whitefield, Prestwich and Bury. Dates depend on installer availability.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Can toughened glass be cut to fit?

No. Cutting or drilling toughened glass makes it shatter, so every pane, hole and notch is made to size before toughening.

Toughened safety glass in nearby towns

Other glazing in Radcliffe

Tell us about the glazing and we will come back with a guide price.