Toughened safety glass in Archway

How much should I budget for toughened safety glass in Archway?

Typical prices for toughened safety glass in Archway are £114 to £414 including VAT (£95 to £345 plus VAT) per pane, supplied and fitted. Use the quote tool for a guide figure, then we survey and confirm a fixed price.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Specification at a glance

Holes, notches and polished edges for frameless fittings
Made to BS EN 12150 and marked for identification
Clear, tinted, obscure, low-iron and sandblasted finishes
Four to five times the strength of annealed glass
Heat-soaked option for large and overhead panes
Single panes or the outer pane of a sealed unit

Fitting in Archway and nearby

Whether you are in central Archway or at the edge of the N19 district, we can arrange a survey. Nearby Holloway and Muswell Hill are covered too.

Greater London has every kind of glazing, from Georgian sashes and Victorian bays in conservation areas to high-street shopfronts, office curtain walling and new-build flats.

Common uses:

Balustrades in a laminated toughened makeup
Frameless office partitions and doors
Glazed doors and side panels
Panes below 800 mm in homes and offices

What to think about first

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Consents and safety: England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Fire-rated glass is different

Glass in fire doors, fire screens and protected escape routes has to be fire-rated glass tested as part of that door or screen system, under Approved Document B and the fire safety duties of the building's responsible person. Laminated and security glass are not fire-rated unless the product says so. Where a pane needs both fire and security performance, it must be a product tested for both.

How it works

Postcode and a few photos
On-site survey
Fixed written price and lead time
Fit, check and explain

Toughened safety glass in Archway: questions

Do you cover Holloway as well as Archway?

Yes. As well as Archway, we can arrange surveys in nearby Holloway, Muswell Hill and Chalk Farm. Dates depend on installer availability.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Why did my toughened glass break on its own?

Occasionally a tiny nickel sulphide inclusion or edge damage causes spontaneous breakage. Heat-soak tested glass reduces the risk for large or high panes.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Toughened safety glass in nearby towns

Other glazing in Archway

Start with a guide price online, then we survey and fix the price in writing.