Toughened safety glass in Solihull

How much should I budget for toughened safety glass in Solihull?

Our guide range for toughened safety glass in Solihull is £114 to £414 including VAT (£95 to £345 plus VAT) per pane, including fitting. The survey is free for new installations and your fixed price follows in writing.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Options for toughened safety glass in Solihull

Breaks into small blunt fragments
Holes, notches and polished edges for frameless fittings
Single panes or the outer pane of a sealed unit
Made to BS EN 12150 and marked for identification
Four to five times the strength of annealed glass
Clear, tinted, obscure, low-iron and sandblasted finishes

Fitting in Solihull and nearby

Solihull is about 7 miles from Birmingham, the main centre for West Midlands. We can survey and fit across the B91 district and in nearby places such as Shirley and Birmingham.

The West Midlands spans Birmingham's city-centre offices and shopping streets, Coventry's post-war precincts, Black Country terraces and long suburban high streets in Wolverhampton and Dudley.

Common uses:

Balustrades in a laminated toughened makeup
Panes below 800 mm in homes and offices
Glazed doors and side panels
Shower screens and splashbacks

What to think about first

Toughened or laminated

Toughened gives strength and safe breakage. Laminated gives safe breakage and stays in place, which is what security needs. Many doors use both in one sealed unit.

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Consents and safety: England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Fire-rated glass is different

Glass in fire doors, fire screens and protected escape routes has to be fire-rated glass tested as part of that door or screen system, under Approved Document B and the fire safety duties of the building's responsible person. Laminated and security glass are not fire-rated unless the product says so. Where a pane needs both fire and security performance, it must be a product tested for both.

How it works

Postcode and a few photos
On-site survey
Fixed written price and lead time
Fit, check and explain

Toughened safety glass in Solihull: questions

Which areas near Solihull do you cover?

We can arrange work in Solihull and in nearby Shirley (2 miles), Birmingham (7 miles) and Kenilworth (9 miles). Dates depend on installer availability.

Can toughened glass be cut to fit?

No. Cutting or drilling toughened glass makes it shatter, so every pane, hole and notch is made to size before toughening.

Is toughened glass a security glass?

No. Toughened glass is strong and breaks safely, but once broken the pane falls out and leaves the opening clear. For security, choose laminated glass or a unit with a laminated pane.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Toughened safety glass in nearby towns

Other glazing in Solihull

Start with a guide price online, then we survey and fix the price in writing.