Toughened safety glass in Surbiton

What should toughened safety glass cost in Surbiton?

As a guide, allow £114 to £414 including VAT (£95 to £345 plus VAT) per pane for toughened safety glass in Surbiton, supplied and fitted. Size, glass makeup, access and frame condition move the price, which is confirmed in writing after the free survey.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Specification at a glance

Holes, notches and polished edges for frameless fittings
Four to five times the strength of annealed glass
Single panes or the outer pane of a sealed unit
Made to measure for each opening
Breaks into small blunt fragments
Made to BS EN 12150 and marked for identification

Fitting in Surbiton and nearby

Whether you are in central Surbiton or at the edge of the KT5 district, we can arrange a survey. Nearby New Malden and Esher are covered too.

Greater London has every kind of glazing, from Georgian sashes and Victorian bays in conservation areas to high-street shopfronts, office curtain walling and new-build flats.

Good candidates for toughened safety glass:

Panes below 800 mm in homes and offices
Frameless office partitions and doors
Shower screens and splashbacks
Balustrades in a laminated toughened makeup

Before the glass is ordered

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Glazing rules in England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Fire-rated glass is different

Glass in fire doors, fire screens and protected escape routes has to be fire-rated glass tested as part of that door or screen system, under Approved Document B and the fire safety duties of the building's responsible person. Laminated and security glass are not fire-rated unless the product says so. Where a pane needs both fire and security performance, it must be a product tested for both.

How it works

Tell us about the glazing
Survey, measuring and frame check
Written quote naming the glass
Fitting and handover

Toughened safety glass in Surbiton: questions

Do you cover New Malden as well as Surbiton?

Yes. As well as Surbiton, we can arrange surveys in nearby New Malden, Esher and Hampton. Dates depend on installer availability.

Is toughened glass a security glass?

No. Toughened glass is strong and breaks safely, but once broken the pane falls out and leaves the opening clear. For security, choose laminated glass or a unit with a laminated pane.

Can toughened glass be cut to fit?

No. Cutting or drilling toughened glass makes it shatter, so every pane, hole and notch is made to size before toughening.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Toughened safety glass in nearby towns

Other glazing in Surbiton

Get a guide price now and book your free survey in Surbiton.