Toughened safety glass in Southall

How much should I budget for toughened safety glass in Southall?

Typical prices for toughened safety glass in Southall are £114 to £414 including VAT (£95 to £345 plus VAT) per pane, supplied and fitted. Use the quote tool for a guide figure, then we survey and confirm a fixed price.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Choices you can make

Heat-soaked option for large and overhead panes
Single panes or the outer pane of a sealed unit
Made to BS EN 12150 and marked for identification
Breaks into small blunt fragments
Four to five times the strength of annealed glass
Made to measure for each opening

Fitting in Southall and nearby

We can arrange toughened safety glass anywhere in Southall, and in nearby Greenford, Heston and Hayes. Tell us your postcode and we will offer dates.

Greater London has every kind of glazing, from Georgian sashes and Victorian bays in conservation areas to high-street shopfronts, office curtain walling and new-build flats.

Common uses:

Panes below 800 mm in homes and offices
Frameless office partitions and doors
Shower screens and splashbacks
Glazed doors and side panels

What to think about first

Barriers and balustrades

Glass that acts as a barrier usually needs a laminated toughened makeup so it stays in place if one ply breaks.

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Consents and safety: England

England

Glazing in workplaces

Regulation 14 of the Workplace (Health, Safety and Welfare) Regulations 1992 requires windows and transparent surfaces in walls, partitions, doors and gates to be of safety material or protected against breakage where health or safety makes that necessary, and to be marked so people notice them. The employer or the person in control of the premises decides what is needed through their risk assessment.

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

How it works

Send sizes or use the quote tool
Free survey at your Southall address
Fixed price in writing
Glass made, then fitted

Toughened safety glass in Southall: questions

Which areas near Southall do you cover?

We can arrange work in Southall and in nearby Greenford (2 miles), Heston (2 miles) and Hayes (2 miles). Dates depend on installer availability.

Can toughened glass be cut to fit?

No. Cutting or drilling toughened glass makes it shatter, so every pane, hole and notch is made to size before toughening.

Why did my toughened glass break on its own?

Occasionally a tiny nickel sulphide inclusion or edge damage causes spontaneous breakage. Heat-soak tested glass reduces the risk for large or high panes.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Toughened safety glass in nearby towns

Other glazing in Southall

Ready for a price? Use the form or call 0800 088 6248.