Toughened safety glass in Exeter

What should toughened safety glass cost in Exeter?

Typical prices for toughened safety glass in Exeter are £114 to £414 including VAT (£95 to £345 plus VAT) per pane, supplied and fitted. Use the quote tool for a guide figure, then we survey and confirm a fixed price.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Specification at a glance

Single panes or the outer pane of a sealed unit
Four to five times the strength of annealed glass
Made to BS EN 12150 and marked for identification
Made to measure for each opening
Breaks into small blunt fragments
Heat-soaked option for large and overhead panes

Fitting in Exeter and nearby

Whether you are in central Exeter or at the edge of the EX1 district, we can arrange a survey. Nearby Exmouth and Tiverton are covered too.

Devon spans Exeter's Georgian and post-war centre, Plymouth's rebuilt 1950s shopping streets and waterfront offices, and seaside towns where sea air is hard on window frames and seals.

Good candidates for toughened safety glass:

Panes below 800 mm in homes and offices
Glazed doors and side panels
Shower screens and splashbacks
Balustrades in a laminated toughened makeup

Before the glass is ordered

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Glazing rules in England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Fire-rated glass is different

Glass in fire doors, fire screens and protected escape routes has to be fire-rated glass tested as part of that door or screen system, under Approved Document B and the fire safety duties of the building's responsible person. Laminated and security glass are not fire-rated unless the product says so. Where a pane needs both fire and security performance, it must be a product tested for both.

How it works

Postcode and a few photos
On-site survey
Fixed written price and lead time
Fit, check and explain

Toughened safety glass in Exeter: questions

Do you cover Exmouth as well as Exeter?

Yes. As well as Exeter, we can arrange surveys in nearby Exmouth, Tiverton and Newton Abbot. Dates depend on installer availability.

Why did my toughened glass break on its own?

Occasionally a tiny nickel sulphide inclusion or edge damage causes spontaneous breakage. Heat-soak tested glass reduces the risk for large or high panes.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Toughened safety glass in nearby towns

Other glazing in Exeter

Start with a guide price online, then we survey and fix the price in writing.