Toughened safety glass in Crewe

What is the price of toughened safety glass in Crewe?

Typical prices for toughened safety glass in Crewe are £114 to £414 including VAT (£95 to £345 plus VAT) per pane, supplied and fitted. Use the quote tool for a guide figure, then we survey and confirm a fixed price.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

What goes into toughened safety glass

Single panes or the outer pane of a sealed unit
Heat-soaked option for large and overhead panes
Made to measure for each opening
Made to BS EN 12150 and marked for identification
Four to five times the strength of annealed glass
Breaks into small blunt fragments

Fitting in Crewe and nearby

Surveys in Crewe (CW1) are booked around installer availability. We also cover nearby Winsford (7 miles), Kidsgrove (8 miles) and Congleton (11 miles).

Cheshire mixes Chester's Rows and listed black-and-white frontages with Victorian terraces in Crewe and Macclesfield, and business parks and newer estates around Warrington.

This glazing suits:

Balustrades in a laminated toughened makeup
Shower screens and splashbacks
Glazed doors and side panels
Frameless office partitions and doors

Questions we will ask at the survey

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

Toughened or laminated

Toughened gives strength and safe breakage. Laminated gives safe breakage and stays in place, which is what security needs. Many doors use both in one sealed unit.

Building regulations and safety in England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Glazing in workplaces

Regulation 14 of the Workplace (Health, Safety and Welfare) Regulations 1992 requires windows and transparent surfaces in walls, partitions, doors and gates to be of safety material or protected against breakage where health or safety makes that necessary, and to be marked so people notice them. The employer or the person in control of the premises decides what is needed through their risk assessment.

How it works

Send sizes or use the quote tool
Free survey at your Crewe address
Fixed price in writing
Glass made, then fitted

Toughened safety glass in Crewe: questions

Can you survey in Crewe and nearby towns?

Yes. Surveys in Crewe, Winsford and Kidsgrove are booked around installer availability.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Why did my toughened glass break on its own?

Occasionally a tiny nickel sulphide inclusion or edge damage causes spontaneous breakage. Heat-soak tested glass reduces the risk for large or high panes.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Toughened safety glass in nearby towns

Other glazing in Crewe

Ready for a price? Use the form or call 0800 088 6248.

Free quote in Crewe