Toughened safety glass in Selby

Toughened safety glass in Selby: what will it cost?

Budget £114 to £414 including VAT (£95 to £345 plus VAT) per pane for toughened safety glass in Selby, supplied and fitted. Larger panes, thicker makeups and difficult access cost more; the price is fixed in writing after the survey.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

Glass and fitting options

Breaks into small blunt fragments
Made to measure for each opening
Heat-soaked option for large and overhead panes
Made to BS EN 12150 and marked for identification
Clear, tinted, obscure, low-iron and sandblasted finishes
Single panes or the outer pane of a sealed unit

Fitting in Selby and nearby

From the YO8 district we also cover Goole (10 miles) and Pontefract (12 miles). Survey dates depend on installer availability.

North Yorkshire includes York's walled city and listed streets, Harrogate's Victorian stone terraces, Middlesbrough's town centre and coastal Scarborough and Whitby.

Typical settings for toughened safety glass:

Panes below 800 mm in homes and offices
Glazed doors and side panels
Frameless office partitions and doors
Shower screens and splashbacks

Getting the right glass for your building

Toughened or laminated

Toughened gives strength and safe breakage. Laminated gives safe breakage and stays in place, which is what security needs. Many doors use both in one sealed unit.

Heat soaking

Rare nickel sulphide inclusions can make toughened glass break without warning. Heat soaking reduces the risk and is worth specifying for large, high or overhead panes.

What the rules say in England

England

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

Glazing in workplaces

Regulation 14 of the Workplace (Health, Safety and Welfare) Regulations 1992 requires windows and transparent surfaces in walls, partitions, doors and gates to be of safety material or protected against breakage where health or safety makes that necessary, and to be marked so people notice them. The employer or the person in control of the premises decides what is needed through their risk assessment.

How it works

Postcode and a few photos
On-site survey
Fixed written price and lead time
Fit, check and explain

Toughened safety glass in Selby: questions

Can you survey in Selby and nearby towns?

Yes. Surveys in Selby, Goole and Pontefract are booked around installer availability.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Is toughened glass a security glass?

No. Toughened glass is strong and breaks safely, but once broken the pane falls out and leaves the opening clear. For security, choose laminated glass or a unit with a laminated pane.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Toughened safety glass in nearby towns

Other glazing in Selby

Start with a guide price online, then we survey and fix the price in writing.

Free quote in Selby