Toughened safety glass in Ormskirk

What should toughened safety glass cost in Ormskirk?

Our guide range for toughened safety glass in Ormskirk is £114 to £414 including VAT (£95 to £345 plus VAT) per pane, including fitting. The survey is free for new installations and your fixed price follows in writing.

Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.

What you can specify

Made to BS EN 12150 and marked for identification
Clear, tinted, obscure, low-iron and sandblasted finishes
Holes, notches and polished edges for frameless fittings
Four to five times the strength of annealed glass
Heat-soaked option for large and overhead panes
Made to measure for each opening

Fitting in Ormskirk and nearby

We arrange surveys and fitting in Ormskirk and across the L39 postcode district, as well as in nearby Maghull (4 miles) and Skelmersdale (5 miles). Dates depend on installer availability.

Lancashire pairs Victorian terraces and town-centre retail in Preston and Blackburn with Lancaster's Georgian stone streets and the seafront hotels, shops and arcades of Blackpool.

Good candidates for toughened safety glass:

Frameless office partitions and doors
Balustrades in a laminated toughened makeup
Shower screens and splashbacks
Glazed doors and side panels

Before the glass is ordered

Barriers and balustrades

Glass that acts as a barrier usually needs a laminated toughened makeup so it stays in place if one ply breaks.

Measure once, carefully

Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.

Glazing rules in England

England

Glazing in workplaces

Regulation 14 of the Workplace (Health, Safety and Welfare) Regulations 1992 requires windows and transparent surfaces in walls, partitions, doors and gates to be of safety material or protected against breakage where health or safety makes that necessary, and to be marked so people notice them. The employer or the person in control of the premises decides what is needed through their risk assessment.

Safety glass in critical locations

In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.

How it works

Guide price online or by phone
Survey in Ormskirk
Accept the fixed quote
Fitted by glaziers working under our contract

Toughened safety glass in Ormskirk: questions

Do you cover Maghull as well as Ormskirk?

Yes. As well as Ormskirk, we can arrange surveys in nearby Maghull, Skelmersdale and Kirkby. Dates depend on installer availability.

How can I tell if glass is toughened?

Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.

Where must safety glass be used?

In critical locations: in England, Approved Document K covers glazing in and beside doors up to 1,500 mm from the floor and other glazing below 800 mm; Wales has the same idea in its Approved Document N, Scotland in standard 4.8 and Northern Ireland in Part V. Glass there must be safety glass or protected.

Why did my toughened glass break on its own?

Occasionally a tiny nickel sulphide inclusion or edge damage causes spontaneous breakage. Heat-soak tested glass reduces the risk for large or high panes.

Toughened safety glass in nearby towns

Other glazing in Ormskirk

Tell us about the glazing and we will come back with a guide price.