Toughened safety glass in Folkestone: what will it cost?
Guide prices for toughened safety glass in Folkestone are £114 to £414 including VAT (£95 to £345 plus VAT) per pane for supply and fitting. We confirm a fixed price in writing after a free survey, before any glass is ordered.
Toughened safety glass is ordinary glass that has been heated and rapidly cooled so its surface is held in compression, making it four to five times stronger than annealed glass of the same thickness. If it does break, it shatters into small, relatively blunt pieces instead of sharp shards, which is why it is used in doors, low-level panes and frameless partitions.
What goes into toughened safety glass
- Heat-soaked option for large and overhead panes
- Four to five times the strength of annealed glass
- Holes, notches and polished edges for frameless fittings
- Made to BS EN 12150 and marked for identification
- Made to measure for each opening
- Clear, tinted, obscure, low-iron and sandblasted finishes
Fitting in Folkestone and nearby
Surveys in Folkestone (CT19) are booked around installer availability. We also cover nearby Dover (7 miles), Ashford (13 miles) and Deal (14 miles).
Kent ranges from Canterbury's listed city centre and the Regency fronts of Tunbridge Wells to the Medway towns, Ashford's growth estates and coastal Margate and Folkestone.
Typical settings for toughened safety glass:
- Frameless office partitions and doors
- Shower screens and splashbacks
- Glazed doors and side panels
- Panes below 800 mm in homes and offices
Getting the right glass for your building
Measure once, carefully
Toughened glass cannot be cut afterwards, so holes and sizes are fixed at the factory. Accurate survey measurements avoid remakes.
Barriers and balustrades
Glass that acts as a barrier usually needs a laminated toughened makeup so it stays in place if one ply breaks.
What the rules say in England
Safety glass in critical locations
In England, section 5 of Approved Document K treats glazing in doors and in side panels within 300 mm of a door edge, from floor level up to 1,500 mm, and any other glazing below 800 mm, as a critical location. Glass there should break safely, be robust, or be guarded. Laminated or toughened glass meeting BS EN 12600 class 3 is the usual answer, rising to class 2 for door and side-panel panes wider than 900 mm.
Glazing in workplaces
Regulation 14 of the Workplace (Health, Safety and Welfare) Regulations 1992 requires windows and transparent surfaces in walls, partitions, doors and gates to be of safety material or protected against breakage where health or safety makes that necessary, and to be marked so people notice them. The employer or the person in control of the premises decides what is needed through their risk assessment.
How it works
- Send sizes or use the quote tool
- Free survey at your Folkestone address
- Fixed price in writing
- Glass made, then fitted
Toughened safety glass in Folkestone: questions
Can you survey in Folkestone and nearby towns?
Yes. Surveys in Folkestone, Dover and Ashford are booked around installer availability.
Is toughened glass a security glass?
No. Toughened glass is strong and breaks safely, but once broken the pane falls out and leaves the opening clear. For security, choose laminated glass or a unit with a laminated pane.
Can toughened glass be cut to fit?
No. Cutting or drilling toughened glass makes it shatter, so every pane, hole and notch is made to size before toughening.
How can I tell if glass is toughened?
Look for a permanent mark etched in a corner naming the standard. Polarised sunglasses can also show faint patterns in toughened glass. We can check during the survey.
Toughened safety glass in nearby towns
Other glazing in Folkestone
- Laminated glass retrofit
- Patio and bifold door security glass
- Security double-glazed units
- Glazing bead security upgrades
- Security glazed doors and screens
- Laminated security glass
Ready for a price? Use the form or call 0800 088 6248.